You're our first priority.
Every time.
LinkReviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. As an Amazon Associate we earn from qualifying purchases. Read more
How frequently should you clean your Dyson vacuum?
Image: Amazon.com
The frequency you use your vacuum, and the severity of your debris determine your vacuum repair plan. Dyson recommends cleaning the Dyson vacuum filter at least once a month to keep your machine operating at peak performance.
If you observe that your Dyson vacuum is not working as well, that the power has diminished, or that cleaning requires more effort on your part, it may be time to clear your Dyson vacuum filter.
How to clean a Dyson vacuum
Image: Amazon.com
1. Purge the container
First and foremost, ensure that you have unplugged the gadget if required.
When the dust receptacle is full, remove it as normal and clear out any remains. Because Dyson vacuum cleaners are bagless vacuum cleaner, do this outside if feasible to avoid allergens and disturbance. Make careful to agitate the container and pry out any obvious obstructions thoroughly.
Most Dyson cordless vacuums can be discharged by pressing a red trigger/button near the handle; however, if you're uncertain, consult your instructions.
2. Cleanse and clean the container
Using a wet microfibre towel, wipe the inside of the canister. Do not immerse the canister vacuum in water; avoid using soap or other cleaning agents. However, you can use pressurized air to reach any odd crannies, but only outside.
3. Take out the filter
While the container is dehydrating, take out the filter. Your vacuum filter is important because it catches large particulates such as dust and pollen and holds them within the vacuum to safeguard the engine and prevent them from being discharged into the air. This filter will undoubtedly become coated and clogged with grit over time and will need to be cleaned.
If you're using a portable variant, the filtration is typically located on the part closest to the handle. If you have an upright type, there is typically one on top of the container and occasionally another in the base of the floor head - both will need to be cleaned. The filtration of a container type is located at the top of the receptacle. If you are uncertain, consult your instructions.
4. Cleanse and dry the filter
Once separated, cautiously remove the filter outside and clear any immediate dust over a receptacle - you can gingerly touch it to disconnect most of it. After that, bring the filter inside, clean it under cold, running water, and wipe it lightly by hand to eliminate any remaining grit.
Fill it with tepid water, cover the holes with your palms, and agitate it slightly to give it one last washing. Repeat the process until the water flows clean. Then agitate the filter to clear any extra liquid and set it aside to air dry for at least 24 hours. Before replacing the filter, make sure it is fully dry.
5. Untangle the brush roll
This is the moment to deal with long strands wound around the brush roll. Cut along the bar with a set of scissors (preferably manicure shears) to eliminate them. Make careful not to drag or push any hairs out of the vacuum, as this could harm it. Be cautious not to harm the hairs while trimming.
You may need to remove the soleplate to reach the brush wheel on some Dyson vacuum cleaners. You can do this with a penny or a flathead screwdriver. In the meantime, make sure to keep the fasteners secure.
6. Inspect the tube for obstructions
You may have a blockage if your Dyson vacuum has stopped working. If this is the case, remove the pipe and examine it. You can slide something long and narrow through to remove an obstruction, such as a broom handle.
If that fails, immerse the pipe in tepid water mixed with white distilled vinegar for 10 minutes before washing. This should remove the obstruction. Allow it to dry fully.
7. Clear the accessories
Remember to inspect your attachments as well. If you frequently use a gap tool or a small powered tool, you should inspect them.
Clear any imminent grime and confined hairs from the tools by hand or, as with the primary brush roll, by using a vacuum. Then, using a wet microfibre towel, clean down the accessories.
8. Clean down the exterior
As a final flourish, use a wet microfibre towel to wash down the exterior of your Dyson vacuum.
Then, allow everything to dry before reassembling. You should allow at least 24 hours for everything to dry before reassembling.
How to maintain your Dyson vacuum cleaner clear for a long time
Image: Amazon.com
-
If possible, use the full power option rarely. Dyson vacuums are designed to operate on auto or traditional settings every day and on maximum strength when necessary. Operating your vacuum on high voltage too frequently will overwork it and increase the likelihood of the filtration becoming blocked.
-
Gather up and dispose of any large detritus before running a cleaner over it.
-
Remember, the more you clear your filter, the less labor you'll have to do when you need to! Clean it frequently to reduce the amount of work required for upkeep.
FAQs
Is it possible to sanitize the inside of a Dyson vacuum?
Once separated, cautiously remove the filter outside and clear any immediate dust over a receptacle - you can gingerly touch it to disconnect most of it. After that, bring the filter inside, clean it under cold, running water, and wipe it lightly by hand to eliminate any remaining grit.
Can I submerge my Dyson head in the water?
The cleaning head assembly should only be cleaned with a wet, lint-free towel and not be washed. Check and cleanse your brush bar frequently to ensure peak performance.
What if I spill water in my Dyson vacuum?
If you suction water, you could harm your vacuum's engine, risk electricity, and create an enormous disturbance. You should only suction water if your vacuum is a wet/dry vacuum certified for water.
Can I submerge my Dyson filter in vinegar?
If your filter is blocked, you may need to clear it with vinegar. Combine equal parts vinegar and water in a basin and submerge the filter for about 15 minutes. Then, flush it with clean water and allow it to dry fully before reattaching it to your vacuum.
Final words
Surely with the above instructions, you already know how to clean a Dyson vacuum. Hope you will take good care of your Dyson vacuum because the best vacuum cleaner is the one that is well taken care of to promote its use.
