How To Clean Shark Vacuum Filters? - 7 Steps

Filters in vacuum cleaners serve a vital purpose by filtering the air before it is circulated back into the room. Thus, the question arises, how do you sanitize shark vacuum filters?

When Should You Replace the Filters in Your Shark Vacuum?

Image: Youtube

Always make sure to clear your vacuum on a frequent basis, whether it's an Upright Shark Navigator, Canister Vertex, Autonomous AI, or PetPro Stick. Emptying dust containers or boxes after each use, or when they reach about half filled, can help keep the vacuum working properly. 

It is recommended to wash down the exterior casing once a month to clear dust and inspect the rollers and cables for knots, blockages, and breakage on a monthly basis. According to Levesque, "we've got precise knowledge on the best way to clean and keep your filters in the best way to clean your filters."

Pre-motor filters should be cleaned every three months, and post-motor filters should be cleaned once a year, according to the Shark Navigator user handbook.

Tools and Materials Required

  • Hardware 

  • A big basin or sink

  • Towels made of microfiber material

  • Nylon-bristled brush Drying stand

  • Garbage bin

  • A pair of tiny shears or a seam remover

  • Materials

  • Both hot and cold water

How To Clean Shark Vacuum Filters?

1. Unplug Shark Vacuum

To sanitize a Shark vacuum, first, disconnect it from power or take it out of its charging dock.

2. Roller Brush Maintenance: Checking and Cleaning

The beater bar or roller brush is an integral part of a vacuum, working to dislodge debris from flooring and carpeting. The effectiveness of a vacuum is diminished if it is impeded from spinning by strands or tangled hair. Cut through the mess with some manicure shears or a fabric remover. Make sure the blade can be turned easily.

3. Empty and clean the dust receptacle

Taking out the vacuum's particulate receptacle. You should throw away the goods. Wipe down the inside and outside of the receptacle with a microfibre towel or scrubber and some tepid water. If you can, uncover the bin's top and movable bottom panels and let it dry out in the air.

4. Verify the Pipe Connections

Now that the trash can is out of the way, you can take the nozzle off and see if it is clogged. Make your way down the tube and check it for any splits or gaps that could compromise the vacuum's pulling power.

It's important to disconnect the tubing from the vacuum's head and clear the area of any debris. To remove obstructions, try using a measure or an outdoor sprinkler. Don't want to ruin the pipe, so take your time.

Clean the pipe with a wet microfibre cloth and reattach it to the correct location.

5. Scrubbing the Screens and Filters

Find the air purifiers and the barriers that prevent particles from getting through. Only use cool water to cleanse the foam and/or felt filters after cleaning them. If you want to keep the filters in good shape, you should avoid using any cleaning products that contain detergent. 

To get rid of dirt, gently compress the filters with your fingertips. Repeat adding new water until the cloudiness disappears. To clear extra water from the filters, roll them in a microfibre cloth. This should not be wrung out.

Clean the filter with a soft-bristled nylon brush (an old toothbrush) if there is grit adhering to it; this works best for pleated filters. Simply rinse the filter in its plastic container under cool running water until the water is clear.

Before replacing the filters, let them air dry for at least 24 hours on a drying stand to eliminate the risk of moisture being pulled into an electrical component.

6. Dwelling System Cleaning

To clean the vacuum's surface, simply use a wet microfibre towel to wash it down. Dust should be cleaned out of any openings that are in close proximity to the engine.

7. Make sure the power cord is in good shape.

Examine the power cable for your Shark cleaner for damage or fraying. When you notice these, it's time to get them fixed.

Disagree that it's too much work? Don't fret; we also offer the "cordless shark cleaner" alternative.

How to Maintain a Spotless Shark Cleaner for Extended Periods of Time

  • Frequently change out the dust container or vacuum bag.

  • If dust buildup is a problem at your house, make sure to change the filters regularly.

  • Every time you use them, wipe the vent covers down to get rid of any grime that has accumulated.


To what extent is it possible to clean the brushes on a Shark vacuum?

You can reuse any of the filters that come with your Shark vacuum, even the HEPA filters, if you have a type that comes with them.

When should the Shark filter be cleaned?

The brushes in your Shark vacuum should be cleaned once a month at the very least and then replaced after they have dried completely.

Can a vacuum screen be cleaned?

Hold the filter under flowing cold water until the water is clear, and any fine residual grit should be washed away. No soap is required, just plain old water.

Do Shark vacuums require regular filter changes?

The HEPA Filter should be changed every three (3) months under typical conditions, but its efficiency could be reduced if you regularly vacuum large quantities of extremely fine grit, powder, or the like.

To what extent does the filtration need to be checked on a Shark vacuum?

The HEPA filtration is an optional extra that comes standard on most Shark vacuum versions. You'll find this in the machine's bottom front, behind the filtration grate (door). To access the HEPA filter, gently pry open the cover and remove it. The filter should be washed thoroughly in clean water and dried completely.

Ultimately Decided Upon

And that's the way to maintain the filtration in your shark vacuum. Does your home not feature a Shark vacuum cleaner? Don't fret; we have the "best-ranked shark vacuum" available right now.

0 ratings